Saturday, 19 December 2015

Computer Knowledge : Network MCQs Class Test Quiz 102

Computer Knowledge : Computer Network MCQs Class Test
IBPS IT Officer Exam Special Quiz

Q.1. The interactive transmission of data within a time sharing system may be best suited to
a. simplex lines
b. half-duplex lines
c. full duplex lines
d. biflex-lines



Q.2. Which of the following statement is incorrect?
a. The difference between synchronous and asynchronous transmission is the clocking derived from the data in synchronous transmission.
b. Half duplex line is a communication line in which data can move in two directions, but not at the same time.
c. Teleprocessing combines telecommunications and DP techniques in online activities
d. Batch processing is the prefered processing mode for telecommunication operation.

Q.3. Which of hte following is considered a broad band communication channel?
a. coaxial cable
b. fiber optics cable
c. microwave circuits
d. all of above

Q.4. Which of the following is not a transmission medium?
a. telephone lines
b. coaxial cables
c. modem
d. microwave systems

Q.5. Which of the following does not allow multiple uses or devices to share one communication line?
a. doubleplexer
b. multiplexer
c. concentrator
d. controller

Q.6. Which of the following signal is not standard RS-232-C signal?
a. VDR
b. RTS
c. CTS
d. DSR

Q.7. Which of the following statement is incorrect?
a. Multiplexers are designed to accept data from several I/O devices and transmit a unified stream of data on one communication line
b. HDLC is a standard synchronous communication protocol.
c. RTS/CTS is the way the DTE indicates that it is ready to transmit data and the way the DCW indicates that it is ready to accept data
d. RTS/CTS is the way the terminal indicates ringing

Q.8. Which of the following is an advantage to using fiber optics data transmission?
a. resistance to data theft
b. fast data transmission rate
c. low noise level
d. all of above

Q.9. Which of the following is required to communicate between two computers?
a. communications software
b. protocol
c. communication hardware
d. all of above including access to transmission medium

Q.10. The transmission signal coding method of TI carrier is called
a. Bipolar
b. NRZ
c. Manchester
d. Binary

Q.11. In OSI network architecture, the dialogue control and token management are responsibility of
a. session layer
b. network layer
c. transport layer
d. data link layer
e. none of above

Q.12. In OSI network architecture, the routing is performed by
a. network layer
b. data link layer
c. transport layer
d. session layer
e. none of above

Q.13. Which of the following performs modulation and demodulation?
a. fiber optics
b. satellite
c. coaxial cable
d. modem
e. none of the above

Q.14. The process of converting analog signals into digital signals so they can be processed by a receiving computer is referred to as:
a. modulation
b. demodulation
c. synchronizing
d. digitising

Q.15. How many OSI layers are covered in the X.25 standard?
a. Two
b. Three
c. Seven
d. Six
e. None of above

Q.16. Layer one of the OSI model is
a. physical layer
b. link layer
c. transport layer
d. network layer
e. none of above

Q.17. The x.25 standard specifies a
a. technique for start-stop data
b. technique for dial access
c. DTE/DCE interface
d. data bit rate
e. none of above

Q.18. Which of the following communication modes support two-way traffic but in only one direction at a time?
a. simplex
b. half duplex
c. three-quarters duplex
d. all of the above
e. none of the above

Q.19. Which of the following might be used by a company to satisfy its growing communications needs?
a. front end processor
b. multiplexer
c. controller
d. concentrator
e. all of the above

Q.20. What is the number of separate protocol layers at the serial interface gateway specified by the X.25 standard?
a. 4
b. 2
c. 6
d. 3
e. all of the above

No comments:

Post a Comment

Advertisement